Call now for a energy audit

Insulation Contractor Serving Historic Fells Point Homes

Licensed & insured insulation + HVAC contractors

Serving Baltimore City & Baltimore County since 2006

Same-day energy audits — we  diagnose first

800+ energy-efficient homes in Baltimore

5.0

Based on Google, Facebook & BBB Reviews

Get Your Estimate

Enter your information below

Reviews

Trusted by Baltimore Homeowners

insulation contractor in Fells Point inspecting blown-in attic insulation with a flashlight to assess energy efficiency

Fells Point sits along Baltimore’s waterfront with 18th-century rowhomes and cobblestone streets. We provide insulation contractor services for Fells Point buildings, including attics, walls, basements, and crawl spaces. Historic district rules require approved materials and methods. Shared-wall rowhomes need vapor barrier coordination.

Flooding zones near the harbor demand moisture-resistant choices. Narrow streets limit truck access and material staging. Insulation Contractor Fells Point specialists understand old construction challenges. Check current availability for your Fells Point address.

Insulation Work Matches Fells Point's Historic Building Requirements

You own a pre-1900 rowhome in the historic district. Approved spray foam and batt choices pass CHAP review. Inspectors check vapor barriers because shared walls trap moisture between homes. We show you material samples before install.

You receive permit copies after we finish. Interior insulation work usually does not need CHAP approval. Exterior foam on visible walls requires pre-approval.

We provide material spec sheets when you need them. Our team knows which products meet historic preservation standards. You avoid delays and rejections. The approval process moves faster when we handle documentation.

Get Your Estimate

Enter your information below

process

Attic Insulation Installation Follows a Clear Step-by-Step Process

You face $300+ winter gas bills in your three-story rowhome. Dense-pack cellulose fills wall cavities without removing historic plaster. Third-floor bedrooms in Fells Point rowhomes overheat in summer without attic barriers.

We run a thermal camera scan to show you cold spots. Follow-up testing confirms your R-value after installation. The dense-pack method works through small holes drilled from inside or outside. Your plaster stays intact throughout the process.

Attic insulation stops heat from escaping through the roof. You see lower energy bills within the first heating season. Our Baltimore insulation contractor team handles historic homes throughout the city. Wall insulation makes upper floors comfortable year-round.

Basement and Crawl Space Protection Against Harbor Moisture

flexible hvac duct installed above blown-in attic insulation by an insulation contractor in Fells Point to improve home efficiency

You live near Thames Street and deal with damp basements after storms. Closed-cell foam blocks water vapor rising through brick foundation walls. Homes within two blocks of the harbor sit in flood zone AE-7. We recommend dehumidifier hookup after foam cures.

Mold testing is available if you request it. The closed-cell foam is rated for flood zones. Your basement surface must be dry before we apply foam.

Moisture barriers protect your foundation from ongoing water exposure. You gain usable storage space below ground. Proper basement insulation keeps first-floor rooms warmer in winter. Foundation protection extends the life of your brick walls.

Scheduling Around Broadway Market Days and Limited Parking

You live on narrow one-way streets like Shakespeare, Ann, or Aliceanna. Early morning start times avoid weekend market crowds. Parking permits are required on most blocks.

Broadway Market Sundays create delays. We confirm material delivery 24 hours ahead. Our truck parks at the nearest legal zone. We apply for temporary permits when needed.

Hand carts move materials if the truck cannot park close. Jobs scheduled for weekdays finish faster. You avoid disruptions during high-traffic hours. Our crews know the best times to access each block.

insulation

How to Reach Our Team from Fells Point Neighborhoods

You live throughout Fells Point and nearby Canton or Upper Fells. We offer quick response times for customers in Baltimore’s 21231 zip code. If you’re coming from the Broadway Square area, just head a few blocks toward Fleet Street and continue past the shops and cafés. Our team serves homes throughout the neighborhood, and we’re easy to find once you’re in the corridor.

You receive same-day or next-day estimates for addresses within two miles of Broadway. Our team knows the area well. We understand local street layouts and parking rules.

Contact us by phone or online form. You get clear answers about timing and availability. Service appointments fit your schedule. We confirm all details before crews arrive.

ATTIC TYPES

Post-Install Checks Confirm Sealed Air Gaps and Code Compliance

attic wood showing mold growth beside blown-in insulation identified during an insulation contractor inspection in Fells Point

You are finalizing a sale contingent on energy upgrades. Blower door test results show 30-50% air leakage reduction. Baltimore City requires R-30 attic insulation for resale inspections.

You receive a signed certificate that matches your permit. Photos document before and after condition. Our quality control team runs final checks on every job. Air sealing work gets tested with diagnostic equipment.

You meet city code without guesswork. Buyers and inspectors see verified results. Final documentation arrives within three business days. Your home passes inspection on the first attempt.

Many homeowners pair insulation upgrades with our HVAC contractor services for complete comfort solutions. Our air conditioning contractor team handles cooling system improvements after insulation work is complete. Combined energy upgrades deliver maximum savings on utility bills.

Get Your Estimate

Enter your information below

faq

FAQs About Insulation & HVAC Services in
Baltimore

1. Can you insulate shared walls in Fells Point rowhomes?

Yes, dense-pack cellulose fills cavities without disturbing your neighbor’s side. Vapor barrier coordination happens if both owners agree. We drill access holes on your side only.

The insulation settles into the full cavity. Your neighbor does not need to participate. Shared walls gain thermal protection. You reduce heat loss between homes.

Interior work is usually exempt from CHAP review. Exterior foam on visible walls requires pre-approval. We provide material spec sheets for your submission.

Most attic and wall projects move forward without delay. Historic preservation rules protect the outside appearance. Interior upgrades follow standard building codes. You stay compliant with both sets of rules.

We apply for temporary permits before your job starts. Scheduling happens around Broadway Market days. Hand carts move materials if the truck cannot park close.

Early morning arrivals avoid traffic buildup. Our drivers know which blocks allow commercial parking. You do not handle permit applications. We manage logistics from start to finish.

Closed-cell foam is rated for flood zones like AE-7. Your surface must be dry before we apply foam. A dehumidifier is recommended after installation.

The foam blocks water vapor from entering. Existing moisture problems need correction first. We inspect your basement before recommending foam. You get a solution designed for waterfront conditions.

Yes, 7 AM starts are available on weekdays. Sunday installs are scheduled after 1 PM when market traffic clears. Early arrivals give us parking access.

You avoid noise complaints from neighbors. Most jobs finish within normal business hours. Weekend work accommodates your schedule. We confirm start times two days in advance.

Most attics finish in four to six hours. Wall dense-pack adds one day per floor. The timeline depends on access and existing conditions.

We give you an estimate after the initial inspection. Multi-floor jobs may span two days. You know the schedule before we begin. Cleanup happens at the end of each work session.

Ready to Lower Your Energy Bills?

Scroll to Top